Hospira
LIFESHIELD LATEX-FREE HEMA Y-TYPE BLOOD SET, Nonvented, 79 Inch with 170 Micron Filter, Prepierced Injection Site and Secure Lock Non-DEHP
49manufacturers in China registered for this device type
24catalogue numbers in this listing
27510(k) clearances naming this product code
40recalls on this code
Who Else Makes It
Concentrated in Zhejiang (12), Jiangsu (11), Shanghai (10). 13 of them are registered as contract manufacturers, able to build to a buyer’s own specification.
| Manufacturer | City | Province | Registered as | Device types |
|---|---|---|---|---|
| Promisemed Hangzhou Meditech Co., Ltd. | Hangzhou | Zhejiang | Contract manufacturer | 21 |
| Hantech Medical Device Co., Ltd. | Cixi | Zhejiang | Contract manufacturer | 18 |
| Forefront Medical Technology (Jiangsu) Co., Ltd. | Changzhou | Jiangsu | Contract manufacturer | 14 |
| BQ Plus Medical Co., Ltd. | Songjiang | Shanghai | Contract manufacturer | 13 |
| Ningbo Tianyi Medical Appliance Co., Ltd. | Ningbo | Zhejiang | Contract manufacturer | 11 |
| Anhui Tiankang Medical Technology Co., Ltd. | Tianchang | Anhui | Contract manufacturer | 9 |
| Anhui Kangda Medical Products Co., Ltd. | Tianchang | Anhui | Contract manufacturer | 7 |
| JDI Electronics Factory | Dongguan | Guangdong | Contract manufacturer | 7 |
| Yangzhou Xingwei Medical Technology Co., Ltd. | Yangzhou | Jiangsu | Contract manufacturer | 5 |
| Wenzhou K.L.F. Medical Plastics Co., Ltd. | Wenzhou | Zhejiang | Contract manufacturer | 4 |
| Advance Technology Ltd | Shenzhen | Guangdong | Contract manufacturer | 3 |
| Weihai Jierui Medical Products Co., Ltd. | Weihai | Shandong | Contract manufacturer | 3 |
Showing 12 of 49. All 49 manufacturers in China registered for Set, Administration, Intravascular
Record
| Listed by | ICU Medical, Inc, United States |
|---|---|
| FDA product code | FPA |
| Device type | Set, Administration, Intravascular |
| Device class | Class 2 |
| Regulation | 21 CFR 880.5440 |
| Establishment | Contract manufacturer, Specification developer, Repacker / relabeller, Complaint-file establishment, Manufacturer |
| 510(k) | K141789 |
| Record published | 2016-09-01 |
| Record revised | 2025-11-24 (version 8) |
Specifications
| MRI safety | Labeling does not contain MRI Safety Information |
|---|---|
| Supplied sterile | Yes |
| Single use | Yes |
| Prescription | Prescription only |
| Latex | Labelled latex-free |
| Label carries | lot or batch number, expiry date |
| Storage | Special storage condition: Room Temperature. Avoid Excessive Heat. Protect from Freezing |
| Packaging | Case of 48, case of 50, case of 20, case of 120, case of 24 |
| Sizes | Length 5 to 145 in |
| UDI direct marking | Exempt |
Catalogue Numbers
| Catalogue number | Size | Status |
|---|---|---|
| 451058 | Approximate priming volume : 3.8 Milliliter | In distribution |
| 2065628 | Length 8 in | In distribution |
| 1990339 | Approximate priming volume : 1.0 Milliliter | In distribution |
| 1422028 | Drop Size : 20 Drops / Milliliter | In distribution |
| 1269402 | Length 80 in | In distribution |
| 1336048 | Length 60 in | In distribution |
| 1114148 | Length 40 in | In distribution |
| 1968228 | Approximate priming volume : 13 Milliliter | In distribution |
| 1159248 | Approximate priming volume : 130 Milliliter | In distribution |
| 1269328 | Length 79 in | In distribution |
| 1269965 | Drop Size : 10 Drops / Milliliter | In distribution |
| 1920948 | Length 80 in | In distribution |
| 460258 | Drop Size : 10 Drops / Milliliter | In distribution |
| 1195448 | Approximate priming volume : 7 Milliliter | In distribution |
| 1990239 | Approximate priming volume : 0.8 Milliliter | In distribution |
| 1990139 | Approximate priming volume : 1.01 Milliliter | In distribution |
| 469301 | Approximate priming volume : 12 Milliliter | In distribution |
| 1171628 | Approximate priming volume : 1.1 Milliliter | In distribution |
| 1154928 | Approximate priming volume : 0.6 Milliliter | In distribution |
| 1494928 | Drop Size : 10 Drops / Milliliter | In distribution |
| 1972128 | Drop Size : 15 Drops / Milliliter | In distribution |
| 303948 | Length 105 in | In distribution |
| 646401 | Approximate priming volume : 3 Milliliter | In distribution |
| 1134920 | Length 82 in | In distribution |
Same Product Code
| Product | Sold by | Catalogue numbers |
|---|---|---|
| ICU Medical | ICU Medical, Inc | 529 |
| Codan | Codan US Corp. | 510 |
| Vygon | Vygon Corp. | 355 |
| Port Access Needle | Bard Access Systems, Inc. | 341 |
| Set, Administration, Intravascular | Mps Medical, Inc. | 291 |
| Alaris, SmartSite | BD Switzerland Sàrl | 266 |
| IV Administration Set | B. Braun Medical Inc. | 242 |
| Medex | ICU Medical, Inc | 237 |
| Extension Set | B. Braun Medical Inc. | 171 |
| MaxGuard | BD Switzerland Sàrl | 150 |
| Medline | Medline Industries, Inc. | 148 |
| Centurion | Centurion Medical Products Corporation | 145 |
Showing 12 of 768. All products under Set, Administration, Intravascular
510(K) Clearances
| Clearance | Decision date |
|---|---|
| K250616 | 2025-06-05 |
| K151969 | 2016-01-19 |
| K100576 | 2010-12-17 |
| K100434 | 2010-07-09 |
| K090189 | 2009-04-10 |
| K082806 | 2009-04-06 |
| K081361 | 2008-08-28 |
| K070532 | 2007-03-20 |
| K053106 | 2006-01-10 |
| K051437 | 2005-08-03 |
| K042182 | 2004-09-01 |
| K040710 | 2004-08-11 |
| K041410 | 2004-07-28 |
| K033290 | 2004-04-12 |
| K021692 | 2003-12-04 |
| K003513 | 2001-01-11 |
| K000472 | 2000-05-10 |
| K974589 | 1998-01-09 |
| K973167 | 1997-11-17 |
| K972712 | 1997-10-01 |
| K970855 | 1997-06-24 |
| K954813 | 1995-11-29 |
| K941190 | 1995-01-31 |
| K940296 | 1994-02-22 |
| K915571 | 1992-09-21 |
| K910546 | 1991-04-29 |
| K840273 | 1984-03-06 |
Recalls
37 of these are Class II. Class II means a temporary or reversible health consequence. Volume alone is not a quality signal: a manufacturer that ships more recalls more.
| Initiated | FDA class | Root cause | Reason | Quantity | Closed |
|---|---|---|---|---|---|
| 2026-05-12 | Not classified | Process control | Intravascular administration tubing set drip chambers may have black specks potentially due to the plastic molding process leaving discolored polyvinyl chloride (PVC) material within the drip chamber wall. The presence of discoloration and | 163,500,199 | |
| 2026-05-12 | Not classified | Process control | Intravascular administration tubing set drip chambers may have black specks potentially due to the plastic molding process leaving discolored polyvinyl chloride (PVC) material within the drip chamber wall. The presence of discoloration and | 100,712,657 | |
| 2026-05-12 | Not classified | Process control | Intravascular administration tubing set drip chambers may have black specks potentially due to the plastic molding process leaving discolored polyvinyl chloride (PVC) material within the drip chamber wall that does not enter the fluid path, | 107,800 | |
| 2025-12-19 | Class II | Process control | Needle free access device intended as accessory to vascular access used in hemodialysis or accessory to intravascular administration sets has a silicone seal which may bulge at the top, separate from the body, tear; may result in fluid leak | 14,684,607 items | |
| 2025-08-06 | Class II | Under Investigation by firm | Certain CADD 50 mL and 100 mL Medication Cassette Reservoirs may exhibit weakened medication bag welds along the bag perimeter inside the plastic housing. This could result in medication leakage along the bag perimeter. | 289098 units | |
| 2025-08-06 | Class II | Under Investigation by firm | Certain CADD 50 mL and 100 mL Medication Cassette Reservoirs may exhibit weakened medication bag welds along the bag perimeter inside the plastic housing. This could result in medication leakage along the bag perimeter. | 29811 units | |
| 2025-08-06 | Class II | Under Investigation by firm | Certain CADD 50 mL and 100 mL Medication Cassette Reservoirs may exhibit weakened medication bag welds along the bag perimeter inside the plastic housing. This could result in medication leakage along the bag perimeter. | 987911 units | |
| 2025-08-06 | Class II | Under Investigation by firm | Certain CADD 50 mL and 100 mL Medication Cassette Reservoirs may exhibit weakened medication bag welds along the bag perimeter inside the plastic housing. This could result in medication leakage along the bag perimeter. | 265500 units | |
| 2025-08-06 | Class II | Under Investigation by firm | Certain CADD 50 mL and 100 mL Medication Cassette Reservoirs may exhibit weakened medication bag welds along the bag perimeter inside the plastic housing. This could result in medication leakage along the bag perimeter. | 211750 units | |
| 2025-08-06 | Class II | Under Investigation by firm | Certain CADD 50 mL and 100 mL Medication Cassette Reservoirs may exhibit weakened medication bag welds along the bag perimeter inside the plastic housing. This could result in medication leakage along the bag perimeter. | 15546 units | |
| 2022-08-01 | Class II | Process control | Due to a manufacturing defect which results in a visible gap between the connector’s top and bottom housing. | Total of all affected units = 5,795,989 units | |
| 2022-08-01 | Class II | Process control | Due to a manufacturing defect which results in a visible gap between the connector’s top and bottom housing. | Total of all affected units = 5,795,989 units | |
| 2022-08-01 | Class II | Process control | Due to a manufacturing defect which results in a visible gap between the connector’s top and bottom housing. | Total of all affected units = 5,795,989 units | |
| 2022-08-01 | Class II | Process control | Due to a manufacturing defect which results in a visible gap between the connector’s top and bottom housing. | Total of all affected units = 5,795,989 units | |
| 2021-03-16 | Class II | Component design/selection | Due to molding defect, there is a potential that certain lots of spinning and non-spinning Sprios male luers may exhibit small amounts of leakage in the inactivated position. | ||
| 2021-03-16 | Class II | Component design/selection | Due to molding defect, there is a potential that certain lots of spinning and non-spinning Sprios male luers may exhibit small amounts of leakage in the inactivated position. | ||
| 2021-03-16 | Class II | Component design/selection | Due to molding defect, there is a potential that certain lots of spinning and non-spinning Sprios male luers may exhibit small amounts of leakage in the inactivated position. | ||
| 2021-03-16 | Class II | Component design/selection | Due to molding defect, there is a potential that certain lots of spinning and non-spinning Sprios male luers may exhibit small amounts of leakage in the inactivated position. | ||
| 2021-03-16 | Class II | Component design/selection | Due to molding defect, there is a potential that certain lots of spinning and non-spinning Sprios male luers may exhibit small amounts of leakage in the inactivated position. | ||
| 2020-08-31 | Class II | Process control | Potential for spinning versions of male luers to exhibit leaks due to a molding defect. Fluid leakage may potentially cause delay of infusion, contamination of the fluid path, exposure to hazardous medications, blood loss, exposure to patie | 19850 | |
| 2020-08-31 | Class II | Process control | Potential for spinning versions of male luers to exhibit leaks due to a molding defect. Fluid leakage may potentially cause delay of infusion, contamination of the fluid path, exposure to hazardous medications, blood loss, exposure to patie | 1856578 | |
| 2020-08-31 | Class II | Process control | Potential for spinning versions of male luers to exhibit leaks due to a molding defect. Fluid leakage may potentially cause delay of infusion, contamination of the fluid path, exposure to hazardous medications, blood loss, exposure to patie | 217522 | |
| 2020-08-31 | Class II | Process control | Potential for spinning versions of male luers to exhibit leaks due to a molding defect. Fluid leakage may potentially cause delay of infusion, contamination of the fluid path, exposure to hazardous medications, blood loss, exposure to patie | 33900 | |
| 2020-08-31 | Class II | Process control | Potential for spinning versions of male luers to exhibit leaks due to a molding defect. Fluid leakage may potentially cause delay of infusion, contamination of the fluid path, exposure to hazardous medications, blood loss, exposure to patie | 37000 | |
| 2020-08-31 | Class II | Process control | Potential for spinning versions of male luers to exhibit leaks due to a molding defect. Fluid leakage may potentially cause delay of infusion, contamination of the fluid path, exposure to hazardous medications, blood loss, exposure to patie | 55000 | |
| 2020-08-31 | Class II | Process control | Potential for spinning versions of male luers to exhibit leaks due to a molding defect. Fluid leakage may potentially cause delay of infusion, contamination of the fluid path, exposure to hazardous medications, blood loss, exposure to patie | 325 | |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
| 2020-07-06 | Class II | Process control | Identification of a potential manufacturing defect on the internal surface of the NanoClave within specific lots of NanoClave sets, which may inhibit a proper seal with the NanoClave spike. | Total of all products (Listed #1 thru 101) = 304735 units | 2023-05-11 |
Source: U.S. FDA establishment registration and device listing records, public domain. Restructured for clarity and searchability. Not affiliated with or endorsed by the FDA. Records are records: nothing here is an offer of sale.